Mechanics and Construction > Mechanics and Construction
Rotor Arm, My current project
Azraels:
Finished the internal belt system that drives the elbow joint. Had to come to a stop today because I'm running out of 6-32 screws which I have been using for most of the construction. As I move closer to the wrist I plan to change to 4-40.
Notice I had to use a set of cog pulleys between shoulder and elbow joint. This was unnecessary and only done because I had no cog belt long enough to reach between joints. Luckily I have plenty of belts at the size I used in case of breakage.
Two of the main things I try to shoot for are the ease of disassemble / reassemble and the strength of the project to not break from being reworked and tested. While I was testing the strength of the shoulder operation the 3 pound weight slipped off the desk jerking the arm back and forth but the shoulder joint / stepper did not budge and held firm.
The linkage after the elbow has been cut short to allow for the addition of the wrist rotation joint.
Wrist rotation, wrist up/down and gripper left to go!
Azraels:
Definitely learning some things with this. Since the last post I have worked on quite a few different things.
The wrist rotation which I'm still not happy with. I will either have to strengthen the mount holding the motor or might change this to another stepper motor. It is currently being actuated by a motor and gearbox pulled from an R/C car which turns a much larger gear. It has plenty of power but the plastic gear box gives when it turns anything heavy which can cause the gear to slip. The bearings for the larger gear/wrist rotation came from a vcr head and were mounted in plastic sleeves which were cut using a wood spade bit grounded (it was old and rusty anyway) down slightly smaller than the bearings.
The pcb for the stepper driver board. Note to self, always triple check connections in Eagle. After everything was soldered on I hooked up the motors and discovered more than one problem. I forgot to ground the ULN-2003's which was an easy fix with solder. Second was mixed up one connection on the MP4502 (these are great and easy to work with for driving higher power steppers!) That required a bit more innovative fix with some jumpers. But finally got it working and went back changed the problem in Eagle just in case I wanted to make another one. Mounted an arduino UNO and the stepper driver to back of turret.
Wrist up down after the wrist rotation. :-[ Was mounting the Arduino the back of the turret today and had the arm raised in the air. I must have bumped and it slipped, smacking the exposed gear at the end of the wrist against the desk breaking the gear. May still be able to use but not sure.
jwatte:
I love how you take low-budget, spare, and surplus parts, poke holes in them, and turn them into functioning machinery! It's inspirational.
Azraels:
Spent the last day and a half working on a basic control GUI in Processing. What I wanted was to be able to hit a button on the screen with my mouse and it move the associated stepper while the mouse button was pressed and stop when mouse button released. Had some issues with the stepper stepping smoothly at first. It sounded pretty rough. I thought this may have been lag time in it reading the serial transmission. After a whole lot of debugging it finally came down to me misplacing a curly brace which solved the whole problem. :P Its running smoothly now. I shooting for my final program to be something like flowstone.
During the testing of the program the cog pulley above the shoulder stepper locked onto the shaft for some reason. I wasn't paying attention and the stepper broke the belt in two. :-[ I had left the motor in the hold position for quite a while and it was quite hot. Not sure if that may have caused some problem or not. May have to make some sort of shield between it and the pulley.
Other than that also worked on securing the wrist rotation motor mount so that it does not give and added a potentiometer to the wrist rotation shaft for some position control. And began experimenting with different types of radio control so that arduino can control its turret rotation wirelessly.
Navigation
[0] Message Index
[*] Previous page
Go to full version