Author Topic: Stripboard. Are there any real disadvantages?  (Read 12621 times)

0 Members and 1 Guest are viewing this topic.

Offline Hal9000Topic starter

  • Supreme Robot
  • *****
  • Posts: 338
  • Helpful? 0
Stripboard. Are there any real disadvantages?
« on: March 03, 2007, 08:59:59 AM »
Hi there,

So far I have only used stripboard for my projects and it works, despite being a bit of a pain.

Is this 'Bit of a pain' the only reason why people etch their boards?  Stripboard circuits may also turn out to be larger, fair enough, but it's cheap and fun!

What do you guys think?
"The truth is, you can't hide from the truth, cos the truth is all there is" - Handsome Boy Modeling School

Offline ed1380

  • Supreme Robot
  • *****
  • Posts: 1,478
  • Helpful? 3
Re: Stripboard. Are there any real disadvantages?
« Reply #1 on: March 03, 2007, 09:44:44 AM »
Even though it's bleedin' obvious (or is it?)...... ;D 
Problems making the $50 robot circuit board?
click here. http://www.societyofrobots.com/robotforum/index.php?topic=3292.msg25198#msg25198

Offline Admin

  • Administrator
  • Supreme Robot
  • *****
  • Posts: 11,703
  • Helpful? 173
    • Society of Robots
Re: Stripboard. Are there any real disadvantages?
« Reply #2 on: March 03, 2007, 11:11:15 AM »
looks like a pain . . .


Offline JesseWelling

  • Expert Roboticist
  • Supreme Robot
  • *****
  • Posts: 707
  • Helpful? 0
  • Only You Can Build A Robot!
Re: Stripboard. Are there any real disadvantages?
« Reply #3 on: March 03, 2007, 01:43:30 PM »
good for learning to think about everything, not good for fast prototyping when you know what you need to.

Offline Eco19R

  • Full Member
  • ***
  • Posts: 104
  • Helpful? 0
Re: Stripboard. Are there any real disadvantages?
« Reply #4 on: March 04, 2007, 02:35:36 AM »
Homebrew PCB aren't that hard - I made one in my garage a day ago.

I use expressPCB, PCB board layout softwear - anyway here are the basic steps to PCB creation just encase anyone didn't know -

Desgin PCB layout - print with laser printer on glossy paper -

Iron on the PCB traces to the board. (literally - use a clothes iron) -

Peel the paper off and touch up with a sharpy any place the toner didn't transfer right.

Submerge in etchant - I use radio shacks Ferric chloride - its "fairly" harmless if you don't heat  up the etchant it'll take about 30  to an hour to etch the board.

Once its done just drill the holes.

I really am not sure how to dispose of the used etchant - radio shack says dilute heavily with water and pour down the drain.

I am gonna check for any chemical disposal places where I live - ( don't want to hurt the environment )
« Last Edit: March 04, 2007, 02:36:11 AM by Eco19R »

Offline JonHylands

  • Expert Roboticist
  • Supreme Robot
  • *****
  • Posts: 562
  • Helpful? 3
  • Robot Builder/ Software Developer
    • Jon's Place
Re: Stripboard. Are there any real disadvantages?
« Reply #5 on: March 04, 2007, 06:06:31 AM »
I generally buy the large Radio Shack perf-boards, the ones with just a zillion round pads on the bottom. I solder wires to run as traces.





Simple to make, simple to fix. Once I have a design cast in stone, and everything works, and I'm sure I'm not going to change anything, I will sometimes get a professionally printed version of it done.

- Jon

Offline JesseWelling

  • Expert Roboticist
  • Supreme Robot
  • *****
  • Posts: 707
  • Helpful? 0
  • Only You Can Build A Robot!
Re: Stripboard. Are there any real disadvantages?
« Reply #6 on: March 04, 2007, 06:23:59 AM »
I agree with John. The round solder pads are the way to go.
If you can get the kind with the solder pads on both sides, or through hole pads those are also good.

Offline Admin

  • Administrator
  • Supreme Robot
  • *****
  • Posts: 11,703
  • Helpful? 173
    • Society of Robots
Re: Stripboard. Are there any real disadvantages?
« Reply #7 on: March 04, 2007, 04:39:59 PM »
Interesting . . . I did not know RadioShack had an etchant kit . . . I think Ill try it out by the end of this year when I have more time . . .
http://www.radioshack.com/product/index.jsp?productId=2102870&cp

I agree with Jon too, the perf board method is the way to go . . . unless of course you want to mass manufacture your board . . . Its all about economies of scale . . .

Offline Hal9000Topic starter

  • Supreme Robot
  • *****
  • Posts: 338
  • Helpful? 0
Re: Stripboard. Are there any real disadvantages?
« Reply #8 on: March 05, 2007, 04:23:29 AM »
Nice replies!

I don't know where I said

"Even though it's bleedin' obvious (or is it?)......  "

But, um, yeah. can't remember!
"The truth is, you can't hide from the truth, cos the truth is all there is" - Handsome Boy Modeling School

Offline ed1380

  • Supreme Robot
  • *****
  • Posts: 1,478
  • Helpful? 3
Re: Stripboard. Are there any real disadvantages?
« Reply #9 on: March 05, 2007, 06:31:07 AM »
http://www.societyofrobots.com/robotforum/index.php?topic=675.msg4121#msg4121
I didn't intend to hurt anyones feelings and if I did, I'm sorrry.
Problems making the $50 robot circuit board?
click here. http://www.societyofrobots.com/robotforum/index.php?topic=3292.msg25198#msg25198

Offline Hal9000Topic starter

  • Supreme Robot
  • *****
  • Posts: 338
  • Helpful? 0
Re: Stripboard. Are there any real disadvantages?
« Reply #10 on: March 05, 2007, 11:34:56 AM »
Nah it's all fun and games! No worries!

Just must have made a profound effect on your vocabulary!
"The truth is, you can't hide from the truth, cos the truth is all there is" - Handsome Boy Modeling School

 


Get Your Ad Here

data_list