Author Topic: Amplifying R/C signal  (Read 5050 times)

0 Members and 1 Guest are viewing this topic.

Offline airman00Topic starter

  • Contest Winner
  • Supreme Robot
  • ****
  • Posts: 3,650
  • Helpful? 21
  • narobo.com
    • Narobo.com - Mechatronics and related
Amplifying R/C signal
« on: January 21, 2008, 11:20:08 AM »
How can I amplify an R/C signal to a helicopter to the maximum distance possible ?

I will post specs for the heli in about half an hour , once I find the manual for the heli.


Thanks,
Eric
Check out the Roboduino, Arduino-compatible board!


Link: http://curiousinventor.com/kits/roboduino

www.Narobo.com

Offline cooldog

  • Supreme Robot
  • *****
  • Posts: 751
  • Helpful? 4
  • be nice to nerds, one day they will be your boss
Re: Amplifying R/C signal
« Reply #1 on: January 21, 2008, 11:22:09 AM »
extend the antenna
robot will rule the world and i will be building them
-admin

favorite web sites
http://www.societyofrobots.com/
http://www.instructables.com/

paulstreats

  • Guest
Re: Amplifying R/C signal
« Reply #2 on: January 21, 2008, 11:27:12 AM »
Give more power to the transmitter if you can. This is a sure fire way of increasing range

Offline HDL_CinC_Dragon

  • Supreme Robot
  • *****
  • Posts: 1,261
  • Helpful? 5
Re: Amplifying R/C signal
« Reply #3 on: January 21, 2008, 11:29:33 AM »
Perhaps making a directional transmission antenna (such as a Cantenna. Google it :)) would help signal strength when your facing it.
United States Marine Corps
Infantry
Returns to society: 2014JAN11

Offline airman00Topic starter

  • Contest Winner
  • Supreme Robot
  • ****
  • Posts: 3,650
  • Helpful? 21
  • narobo.com
    • Narobo.com - Mechatronics and related
Re: Amplifying R/C signal
« Reply #4 on: January 21, 2008, 11:33:02 AM »
Give more power to the transmitter if you can. This is a sure fire way of increasing range


Yes but wouldn't I also have to change some of the components in the transmitter. Like if It is powered by 6V I cant just connect 12V, can I?

also, by more power you mean more voltage or more current, or a combination of both?
Check out the Roboduino, Arduino-compatible board!


Link: http://curiousinventor.com/kits/roboduino

www.Narobo.com

Offline cooldog

  • Supreme Robot
  • *****
  • Posts: 751
  • Helpful? 4
  • be nice to nerds, one day they will be your boss
Re: Amplifying R/C signal
« Reply #5 on: January 21, 2008, 11:34:26 AM »
don't jump from 6v to 12v

start slowly like add another battery to make it 7.5v
robot will rule the world and i will be building them
-admin

favorite web sites
http://www.societyofrobots.com/
http://www.instructables.com/

Offline ed1380

  • Supreme Robot
  • *****
  • Posts: 1,478
  • Helpful? 3
Re: Amplifying R/C signal
« Reply #6 on: January 21, 2008, 12:13:57 PM »
would an op amp work?

I'm sure you can get sample chips for amplifying radio signals.
I've seen them for audio signals
Problems making the $50 robot circuit board?
click here. http://www.societyofrobots.com/robotforum/index.php?topic=3292.msg25198#msg25198

Offline airman00Topic starter

  • Contest Winner
  • Supreme Robot
  • ****
  • Posts: 3,650
  • Helpful? 21
  • narobo.com
    • Narobo.com - Mechatronics and related
Re: Amplifying R/C signal
« Reply #7 on: January 21, 2008, 12:18:39 PM »
no like how would I actually go about amplifying it .

connect an op amp to the wire connecting to the antenna or perhaps connect an op amp to the reciever end?


would powering it with a larger voltage do anything?

what's also weird is that I cannot find any retailer of r/c amplifiers out there.
Check out the Roboduino, Arduino-compatible board!


Link: http://curiousinventor.com/kits/roboduino

www.Narobo.com

Offline Kagi

  • Jr. Member
  • **
  • Posts: 22
  • Helpful? 0
Re: Amplifying R/C signal
« Reply #8 on: January 21, 2008, 12:27:43 PM »
You might check these boards. There is a massive amount of knowledge on them about RC. http://www.rcgroups.com/forums/index.php . Hope it helps.

Offline airman00Topic starter

  • Contest Winner
  • Supreme Robot
  • ****
  • Posts: 3,650
  • Helpful? 21
  • narobo.com
    • Narobo.com - Mechatronics and related
Re: Amplifying R/C signal
« Reply #9 on: January 21, 2008, 12:36:44 PM »
thanks I will post a question over there
Check out the Roboduino, Arduino-compatible board!


Link: http://curiousinventor.com/kits/roboduino

www.Narobo.com

Offline Admin

  • Administrator
  • Supreme Robot
  • *****
  • Posts: 11,703
  • Helpful? 173
    • Society of Robots
Re: Amplifying R/C signal
« Reply #10 on: January 25, 2008, 09:23:02 PM »
yeap an op-amp will work . . . make sure its a high frequency amplifier . . . like 72MHz+ ;)

also, make your antennas parallel for maximum range

Offline ed1380

  • Supreme Robot
  • *****
  • Posts: 1,478
  • Helpful? 3
Re: Amplifying R/C signal
« Reply #11 on: January 25, 2008, 10:38:40 PM »
i got a Q admin. would the op amp be put on the receiving or transmitting side?
Problems making the $50 robot circuit board?
click here. http://www.societyofrobots.com/robotforum/index.php?topic=3292.msg25198#msg25198

Offline Admin

  • Administrator
  • Supreme Robot
  • *****
  • Posts: 11,703
  • Helpful? 173
    • Society of Robots
Re: Amplifying R/C signal
« Reply #12 on: January 25, 2008, 10:42:50 PM »
at least the transmitting end, but you can do it on both for double the amp fun ;D

paulstreats

  • Guest
Re: Amplifying R/C signal
« Reply #13 on: January 26, 2008, 08:17:41 AM »
I would personally just use one at the transmitting end since its the tranmitted signal that you need to amplify. If you use one at the receiving end then you will be amplifying any noise and interference as well the signal.

Remember admins suggestion for a high speed op amp. The faster the better

Offline Steel_monkey

  • Full Member
  • ***
  • Posts: 85
  • Helpful? 0
Re: Amplifying R/C signal
« Reply #14 on: January 26, 2008, 10:07:14 AM »
If you need more distance-> you need more power-> you need power amplifier, not voltage amplifier. I am not sure opamp will help- its output power is low, it is not designed for power amplification ( taking in account 80 MHz bandwidth). As I saw in my tiny Dragonfly 5#5 transmitter,  output amplifier is simple 1-transistor A-class power amp (I can see closer if anybody is interested).
About basic electronics I personnaly reccomend "The art of Electronics", Horowitz and Hill (called Electronics Byble).

Offline Admin

  • Administrator
  • Supreme Robot
  • *****
  • Posts: 11,703
  • Helpful? 173
    • Society of Robots
Re: Amplifying R/C signal
« Reply #15 on: January 26, 2008, 10:25:32 AM »
there are power amps you can get, but yea, not sure on frequency.

a MOSFET *might* be capable of doing this . . . not sure on frequency though . . .

Offline Steel_monkey

  • Full Member
  • ***
  • Posts: 85
  • Helpful? 0
Re: Amplifying R/C signal
« Reply #16 on: January 26, 2008, 01:29:38 PM »
I just made little search- here is nearly standard schematic for power amplifier. This is D class, mine is A class ( they just don`t care about my batteries). Output inductors and caps match amplifier output with antenna.
Personally, I would not even try to do something with 80-MHz until I had access to the fast scope (at least). 

Offline airman00Topic starter

  • Contest Winner
  • Supreme Robot
  • ****
  • Posts: 3,650
  • Helpful? 21
  • narobo.com
    • Narobo.com - Mechatronics and related
Re: Amplifying R/C signal
« Reply #17 on: March 16, 2009, 07:27:12 PM »
*Reviving topic*
I'm looking to amplify the Sparkfun RF modules - the ones I used here http://narobo.com/articles/rfmodules.html

So what would I do to amplify the transmitter range , I'm clueless here. Connect the op amp to what?
Thanks in advance
Check out the Roboduino, Arduino-compatible board!


Link: http://curiousinventor.com/kits/roboduino

www.Narobo.com

Offline Admin

  • Administrator
  • Supreme Robot
  • *****
  • Posts: 11,703
  • Helpful? 173
    • Society of Robots
Re: Amplifying R/C signal
« Reply #18 on: March 25, 2009, 12:57:48 AM »
Hook up an oscilloscope between ground and antenna output and see what signals it emits.

You can probably use a MOSFET and a larger voltage source to amplify the output (I'll leave it up to you to figure that one out).

Offline dunk

  • Expert Roboticist
  • Supreme Robot
  • *****
  • Posts: 1,086
  • Helpful? 21
    • dunk's robot
Re: Amplifying R/C signal
« Reply #19 on: March 25, 2009, 03:36:41 AM »
if you poke around on Digikey you will find lots of dedicated RF amplifiers.
digikey.com -> RF and RFID -> RF Amplifier ICs and Modules
takes you here: http://search.digikey.com/scripts/DkSearch/dksus.dll?Cat=3539647
there are 1,575 items though so picking the one you want might take a little time...

the datasheets for these components should tell you how to use them but in general they are connected to the between the transmitter and the outgoing antenna.


dunk.

 


Get Your Ad Here

data_list