Author Topic: Basic Stamp 2sx tutorial  (Read 3543 times)

0 Members and 1 Guest are viewing this topic.

Offline AudacityTopic starter

  • Jr. Member
  • **
  • Posts: 22
  • Helpful? 0
Basic Stamp 2sx tutorial
« on: December 22, 2009, 07:52:21 PM »
Well first off before i get a 100 messages saying how much basic stamps suck to save you the time i know that ;)
ok here my question: theirs a really good tutorial on here (http://www.societyofrobots.com/member_tutorials/node/26) about how to build a parallax BS2sx microcontroller (normally $60.00) for $30.00 (or less now because some of the stuff cost less now) and it really seems like a good idea .. but the tutorial dates back to 2007 and the user has not logged on sense then and hence making the tutorial not outdated but full of dead links. the first problem i have is that the website he listed to buy the basic parts doesn't look reliable (www.jamco.com)....it just seems fishy. also as noted above the schematic link is dead and im not the best at electronics so i cant tell by the picture what goes where . my last problem is that the EEPROM name in the part list is different from the link he gave us.

              Thanks to all in advance

Offline SmAsH

  • Supreme Robot
  • *****
  • Posts: 3,959
  • Helpful? 75
  • SoR's Locale Electronics Nut.
Re: Basic Stamp 2sx tutorial
« Reply #1 on: December 22, 2009, 08:00:43 PM »
First of all, that site is dead. Second, why do you want to build it exactly as a basic stamp is, why not customize it?
Howdy

Offline AudacityTopic starter

  • Jr. Member
  • **
  • Posts: 22
  • Helpful? 0
Re: Basic Stamp 2sx tutorial
« Reply #2 on: December 22, 2009, 08:08:14 PM »
that explains it and what do you mean by customise it ??? If your wondering why im building it its because

. Fun
. Challenge
. i have only used basic stamps....... :D........Swicthin over to ardouino and C soon though 8)
. a cheaper option then buy n 60$ of premade unfun
. Fun
« Last Edit: December 22, 2009, 08:54:45 PM by Audacity »

Offline SmAsH

  • Supreme Robot
  • *****
  • Posts: 3,959
  • Helpful? 75
  • SoR's Locale Electronics Nut.
Re: Basic Stamp 2sx tutorial
« Reply #3 on: December 22, 2009, 08:10:00 PM »
Hmm, if you are planning to switch to avr, why not take a look at the $50 robot board.
It only costs ~$15 to make and is more useful than the stamp.
Howdy

Offline AudacityTopic starter

  • Jr. Member
  • **
  • Posts: 22
  • Helpful? 0
Re: Basic Stamp 2sx tutorial
« Reply #4 on: December 22, 2009, 08:12:55 PM »
Avr? you mean arduino ....... yea im a noob... also i have looked at that but i still wanna do stuff with stamps

Offline SmAsH

  • Supreme Robot
  • *****
  • Posts: 3,959
  • Helpful? 75
  • SoR's Locale Electronics Nut.
Re: Basic Stamp 2sx tutorial
« Reply #5 on: December 22, 2009, 08:15:06 PM »
The main chip in the arduino is an avr.
But if you are set on making a stamp, thats that.
What do you need help with?
Howdy

Offline AudacityTopic starter

  • Jr. Member
  • **
  • Posts: 22
  • Helpful? 0
Re: Basic Stamp 2sx tutorial
« Reply #6 on: December 22, 2009, 08:21:16 PM »
Well first i know i could probably get the parts some where else but the 16K Bytes EEPROM and the link do not match up.... i think well http://www.parallax.com/StoreSearchResults/tabid/768/txtSearch/602-00013/List/0/SortField/4/ProductID/25/Default.aspx thats the title but in the parts list it only says 16k bytes EEPROM
another thing is schematics..... not the best with electronics

Offline SmAsH

  • Supreme Robot
  • *****
  • Posts: 3,959
  • Helpful? 75
  • SoR's Locale Electronics Nut.
Re: Basic Stamp 2sx tutorial
« Reply #7 on: December 22, 2009, 08:25:36 PM »
That is the right chip, the tutorial must have an error.
Howdy

Offline AudacityTopic starter

  • Jr. Member
  • **
  • Posts: 22
  • Helpful? 0
Re: Basic Stamp 2sx tutorial
« Reply #8 on: December 22, 2009, 08:26:43 PM »
Here is the parts list:
2N3904 NPN transistors…………Jamco part#: 38359…………….$0.069............x2
2N3906 PNP transistor…………..Jamco part#: 38375……………..$0.051............x1
0.1uF capacitors………………….Jamco part#: 151118……………$0.155...............x2
10uF cap capacitor……………….Jamco part#: 330692…………....$0.039.............x1
 1.5pF capacitor……………………Jamco part#: 332188…………...$0.056................x1
4.7K resistors……………………..Jamco part#: 691024…………...$0.01..................x2
10k resistors………………………Jamco part#: 691104…………...$0.01..................x8
50 MHz resinator …………………Parallax part#: 250-05060…….$1.95..............x1
9 pin female conector……………..Jamco part#: 104978…………..$0.96..............x1
LM2940-5.0 5volt regulator……….Parallax part#: 601-00506…….$1.85............x1
16K Bytes EEPROM………………Parallax part#: 602-00013…….$5.95............x1
BS2sx interpiter chip………………Parallax part#: PBASIC2SX/P...$12.00..........x1
1 bread bord and jumper kit.....................................................................x1

Offline AudacityTopic starter

  • Jr. Member
  • **
  • Posts: 22
  • Helpful? 0
Re: Basic Stamp 2sx tutorial
« Reply #9 on: December 22, 2009, 08:27:42 PM »
oh ok i should buy that one

Offline Razor Concepts

  • Supreme Robot
  • *****
  • Posts: 1,856
  • Helpful? 53
    • RazorConcepts
Re: Basic Stamp 2sx tutorial
« Reply #10 on: December 22, 2009, 08:28:10 PM »
The novelty of making your own on a breadboard will wear out once you realize how horrible a microcontroller system on a breadboard is  ;)

Offline AudacityTopic starter

  • Jr. Member
  • **
  • Posts: 22
  • Helpful? 0
Re: Basic Stamp 2sx tutorial
« Reply #11 on: December 22, 2009, 08:29:55 PM »
hmmm..... really well why is it so bad? also how is he programming it?
What is he using to connect to the CPU
« Last Edit: December 22, 2009, 08:34:01 PM by Audacity »

Offline SmAsH

  • Supreme Robot
  • *****
  • Posts: 3,959
  • Helpful? 75
  • SoR's Locale Electronics Nut.
Re: Basic Stamp 2sx tutorial
« Reply #12 on: December 22, 2009, 08:41:17 PM »
There must be pins he plugs the programmer into.
Razor is right, breadboarded circuits are terrible. Once you've made it and tested it, move it to a proto board.
Howdy

Offline AudacityTopic starter

  • Jr. Member
  • **
  • Posts: 22
  • Helpful? 0
Re: Basic Stamp 2sx tutorial
« Reply #13 on: December 22, 2009, 08:46:38 PM »
ok i will :)
              btw what do you mean programmer i have the  "Whats a Microcontroller"  serial cord but does that count as a programmer and how do you hook it up btw sorry for the wave of questions
http://www.radioshack.com/product/index.jsp?productId=2117994

Offline SmAsH

  • Supreme Robot
  • *****
  • Posts: 3,959
  • Helpful? 75
  • SoR's Locale Electronics Nut.
Re: Basic Stamp 2sx tutorial
« Reply #14 on: December 22, 2009, 08:52:20 PM »
If it connects the microcontroller up the your pc it should work...
Sorry, im not too familiar with stamps :-\
Howdy

Offline AudacityTopic starter

  • Jr. Member
  • **
  • Posts: 22
  • Helpful? 0
Re: Basic Stamp 2sx tutorial
« Reply #15 on: December 22, 2009, 08:54:10 PM »
thats fine and it does :)
ok one more leap before i start buying..... the schematic problem......

Offline SmAsH

  • Supreme Robot
  • *****
  • Posts: 3,959
  • Helpful? 75
  • SoR's Locale Electronics Nut.
Re: Basic Stamp 2sx tutorial
« Reply #16 on: December 22, 2009, 08:57:50 PM »
Whats the problem with it?
Howdy

Offline AudacityTopic starter

  • Jr. Member
  • **
  • Posts: 22
  • Helpful? 0
Re: Basic Stamp 2sx tutorial
« Reply #17 on: December 22, 2009, 08:59:05 PM »
the links dead :(

Offline AudacityTopic starter

  • Jr. Member
  • **
  • Posts: 22
  • Helpful? 0
Re: Basic Stamp 2sx tutorial
« Reply #18 on: December 22, 2009, 09:00:46 PM »
wait nvm........gonna go buy stuff :)

Offline SmAsH

  • Supreme Robot
  • *****
  • Posts: 3,959
  • Helpful? 75
  • SoR's Locale Electronics Nut.
Re: Basic Stamp 2sx tutorial
« Reply #19 on: December 22, 2009, 09:02:45 PM »
http://www.parallax.com/dl/docs/prod/schem/bs2sxrevd.pdf
lol, it took me a while to get what was wrong XD
Howdy

Offline AudacityTopic starter

  • Jr. Member
  • **
  • Posts: 22
  • Helpful? 0
Re: Basic Stamp 2sx tutorial
« Reply #20 on: December 22, 2009, 09:03:54 PM »
yea me to :D gonna go buy stuff now thanks for the help

Offline waltr

  • Supreme Robot
  • *****
  • Posts: 1,944
  • Helpful? 99
Re: Basic Stamp 2sx tutorial
« Reply #21 on: December 23, 2009, 10:20:56 AM »

Offline AudacityTopic starter

  • Jr. Member
  • **
  • Posts: 22
  • Helpful? 0
Re: Basic Stamp 2sx tutorial
« Reply #22 on: December 23, 2009, 10:32:09 AM »
thanks :)

 


Get Your Ad Here