go away spammer

Author Topic: fabricate Robotic arm with options to change the gripper type  (Read 3568 times)

0 Members and 1 Guest are viewing this topic.

Offline a7madeTopic starter

  • Beginner
  • *
  • Posts: 3
  • Helpful? 0
is it possible to fabricate 5DOF robotic arm with option to change the gripper type automatic using Servo motors??

Examples:
•   Gripper for holding hot objects (hot machined parts).
•   Gripper for holding fragile object (glass, brittle).
•   Gripper with sharp Edges to cut the materials

1 DOF base
1 DOF Shoulder
1 DOF Elbow
2 DOF Gripper

Offline waltr

  • Supreme Robot
  • *****
  • Posts: 1,944
  • Helpful? 99
Re: fabricate Robotic arm with options to change the gripper type
« Reply #1 on: October 31, 2010, 09:11:19 AM »
Quote
is it possible ...??
yes
« Last Edit: October 31, 2010, 07:10:10 PM by waltr »

Offline photomark

  • Jr. Member
  • **
  • Posts: 44
  • Helpful? 0
Re: fabricate Robotic arm with options to change the gripper type
« Reply #2 on: October 31, 2010, 04:22:51 PM »
Very possible and also very complicated   

Offline a7madeTopic starter

  • Beginner
  • *
  • Posts: 3
  • Helpful? 0
Re: fabricate Robotic arm with options to change the gripper type
« Reply #3 on: November 01, 2010, 08:38:19 AM »
can i use 8051 Microcontroller in this project? if no, what type of Microcontroller i must choose?

Offline waltr

  • Supreme Robot
  • *****
  • Posts: 1,944
  • Helpful? 99
Re: fabricate Robotic arm with options to change the gripper type
« Reply #4 on: November 01, 2010, 01:22:40 PM »
It depends on your design parameters. It may be done with an 8051 as you only have 5 motors to control depending on how they are to be controlled and on the method and precision of any required feed-back. If your requirements are tight then you may need an 8051 for each joint but all this is just guesses since I don't know what you really need.

Offline a7madeTopic starter

  • Beginner
  • *
  • Posts: 3
  • Helpful? 0
Re: fabricate Robotic arm with options to change the gripper type
« Reply #5 on: November 29, 2010, 11:24:50 PM »
What kind of material i should use for the gripper that hold hot objects?

Offline Conscripted

  • Robot Overlord
  • ****
  • Posts: 291
  • Helpful? 10
Re: fabricate Robotic arm with options to change the gripper type
« Reply #6 on: December 02, 2010, 07:29:57 AM »
Well.... Hot is a relative term. How hot are you talking? Cooking hot or melting metal hot?

Offline Soeren

  • Supreme Robot
  • *****
  • Posts: 4,672
  • Helpful? 227
  • Mind Reading: 0.0
Re: fabricate Robotic arm with options to change the gripper type
« Reply #7 on: December 02, 2010, 09:44:52 AM »
... And ...
What is the maximum duration to hold these hot objects and what is the cool down time (the time from releasing one object to picking up the next).

How long can they be from the fixture point.


Materials like cast iron and stainless steel transfers heat relatively slow, but keep the heat for quite a while. Aluminum OTOH picks up the heat very fast, but dissipates it fast as well - with careful selection of materials and design/construction, it could hold metal glowing cherry red (for a certain amount of time).
Regards,
Søren

A rather fast and fairly heavy robot with quite large wheels needs what? A lot of power?
Please remember...
Engineering is based on numbers - not adjectives

 


Get Your Ad Here

data_list