go_away

Author Topic: #4 screw  (Read 3330 times)

0 Members and 1 Guest are viewing this topic.

Offline airman00Topic starter

  • Contest Winner
  • Supreme Robot
  • ****
  • Posts: 3,653
  • Helpful? 21
  • narobo.com
#4 screw
« on: December 17, 2007, 02:49:31 PM »
I need to make a hole on a CAD

What size diameter does a #4 machine screw go through?   Would 3/8" be good?

P.S. I cannot test it out tonight and so I need an answer today
Check out the Roboduino, Arduino-compatible board!


Link: http://curiousinventor.com/kits/roboduino

www.Narobo.com

Offline JonHylands

  • Expert Roboticist
  • Supreme Robot
  • *****
  • Posts: 562
  • Helpful? 3
  • Robot Builder/ Software Developer
Re: #4 screw
« Reply #1 on: December 17, 2007, 03:06:40 PM »
A #4-40 machine screw goes through a 1/8" hole without touching the sides. 7/64 makes a much tighter fit, but hard to slide in and out. I usually drill my #4-40 clearance holes to 1/8".

If you want to drill a hole to tap for #4-40, you need to drill a hole using a #43 drill bit, which is roughly 0.089".

- Jon

Offline SomeSaba

  • Full Member
  • ***
  • Posts: 75
  • Helpful? 0
Re: #4 screw
« Reply #2 on: December 17, 2007, 04:23:50 PM »
does anyone have a site that has a chart for all these?

They come in handy.. and i can never find them online

Offline JonHylands

  • Expert Roboticist
  • Supreme Robot
  • *****
  • Posts: 562
  • Helpful? 3
  • Robot Builder/ Software Developer
Re: #4 screw
« Reply #3 on: December 17, 2007, 05:03:57 PM »

Offline airman00Topic starter

  • Contest Winner
  • Supreme Robot
  • ****
  • Posts: 3,653
  • Helpful? 21
  • narobo.com
Re: #4 screw
« Reply #4 on: December 17, 2007, 06:36:29 PM »
Thanks guys,
 i got this equation to convert # into inches


Diameter = ( # x .013") + .06" 
So a #4 screw would be .58" in diameter

Check out the Roboduino, Arduino-compatible board!


Link: http://curiousinventor.com/kits/roboduino

www.Narobo.com

Offline JonHylands

  • Expert Roboticist
  • Supreme Robot
  • *****
  • Posts: 562
  • Helpful? 3
  • Robot Builder/ Software Developer
Re: #4 screw
« Reply #5 on: December 17, 2007, 06:58:30 PM »
Your equation is probably correct, but your math is way off.

(4 * 0.013") + 0.06" = 0.112"

- Jon

Offline airman00Topic starter

  • Contest Winner
  • Supreme Robot
  • ****
  • Posts: 3,653
  • Helpful? 21
  • narobo.com
Re: #4 screw
« Reply #6 on: December 17, 2007, 08:02:52 PM »
Your equation is probably correct, but your math is way off.

(4 * 0.013") + 0.06" = 0.112"

- Jon


lol  , i realized that !  ;D  I was about to go back and correct the post, since I realized a .58" diameter screw is pretty thick, way too think for a #4/

anyway I used a 5/32" bit
Check out the Roboduino, Arduino-compatible board!


Link: http://curiousinventor.com/kits/roboduino

www.Narobo.com

Offline JonHylands

  • Expert Roboticist
  • Supreme Robot
  • *****
  • Posts: 562
  • Helpful? 3
  • Robot Builder/ Software Developer
Re: #4 screw
« Reply #7 on: December 17, 2007, 08:32:05 PM »
5/32" will be way too big - your screw will wobble like crazy.

5/32" = 0.156"

I typically use 1/8", which is 0.125"...

- Jon

Offline airman00Topic starter

  • Contest Winner
  • Supreme Robot
  • ****
  • Posts: 3,653
  • Helpful? 21
  • narobo.com
Re: #4 screw
« Reply #8 on: December 17, 2007, 08:36:00 PM »
thanks jon    ;D

1/8 it is !   ;)

i think i'm going to go to sleep now, i had no sleep in the past 24 hours

Check out the Roboduino, Arduino-compatible board!


Link: http://curiousinventor.com/kits/roboduino

www.Narobo.com

 


Get Your Ad Here

data_list