go_away

Author Topic: Help me design Line follower using ATMega32 Please  (Read 3745 times)

0 Members and 1 Guest are viewing this topic.

Offline mystyleonfireTopic starter

  • Beginner
  • *
  • Posts: 5
  • Helpful? 0
Help me design Line follower using ATMega32 Please
« on: June 19, 2008, 10:45:14 AM »
Hi folks,
 Im Karthik from India. I am a beginer to line follower. And I would like to have some guidance about the circuit. Please help.

Offline Admin

  • Administrator
  • Supreme Robot
  • *****
  • Posts: 11,663
  • Helpful? 169
    • Society of Robots

Offline mystyleonfireTopic starter

  • Beginner
  • *
  • Posts: 5
  • Helpful? 0
Re: Help me design Line follower using ATMega32 Please
« Reply #2 on: June 21, 2008, 07:21:44 PM »
Yes, I have seen iit. But i need to design using ATMega32 MC.

Offline Admin

  • Administrator
  • Supreme Robot
  • *****
  • Posts: 11,663
  • Helpful? 169
    • Society of Robots
Re: Help me design Line follower using ATMega32 Please
« Reply #3 on: June 21, 2008, 07:45:11 PM »
Why the mega32?

Read the bottom of this page:
http://www.societyofrobots.com/step_by_step_atmega168_swapout.shtml

Then read the rest of the page . . .

Offline mystyleonfireTopic starter

  • Beginner
  • *
  • Posts: 5
  • Helpful? 0
Re: Help me design Line follower using ATMega32 Please
« Reply #4 on: June 21, 2008, 07:50:48 PM »
Oh, Thats cool. So, only the pin out are different. Means, If VCC and Port 1 for ATMega8 is 1st and the 19th pin(for example), then if the VCC and Port A for ATMega 32 are 20th and 16th pin. are they same? if i do the connections according to it, will it work out?im jst a beginer.

Offline Admin

  • Administrator
  • Supreme Robot
  • *****
  • Posts: 11,663
  • Helpful? 169
    • Society of Robots
Re: Help me design Line follower using ATMega32 Please
« Reply #5 on: June 21, 2008, 07:59:32 PM »
Yeap!

Offline mystyleonfireTopic starter

  • Beginner
  • *
  • Posts: 5
  • Helpful? 0
Re: Help me design Line follower using ATMega32 Please
« Reply #6 on: June 21, 2008, 08:02:47 PM »
ok. Thanks a lot. And can u guide me thru the processes? PLease...

Offline Admin

  • Administrator
  • Supreme Robot
  • *****
  • Posts: 11,663
  • Helpful? 169
    • Society of Robots
Re: Help me design Line follower using ATMega32 Please
« Reply #7 on: June 21, 2008, 08:32:16 PM »
Just post what you think the schematic will be, and we can verify it for you before you wire it up.

(its very very similar to the $50 Robot schematic, so after a little thought it should make sense to you)

Offline mystyleonfireTopic starter

  • Beginner
  • *
  • Posts: 5
  • Helpful? 0
Re: Help me design Line follower using ATMega32 Please
« Reply #8 on: June 21, 2008, 08:34:00 PM »
OK.... Thank u a lott. :)

 


Get Your Ad Here

data_list