A colleague of mine expressed concerns over how I will deal with the heat generated by the motors and other electronics. He pointed out that all these motors are going to generate heat while running and the silicone skin will prevent that heat from escaping. This was a great observation and one that must necessarily be addressed as it is a make or break problem that the entire success of the project hinges upon. In fact, it is so important that I spent a great deal of time designing and planning multiple redundant cooling systems for the robot to absolutely ENSURE that heat does not end up being my greatest downfall of the whole project which could easily be the case if not handled properly. To start, I have designed artificial lungs that will draw in cool outside air, expel that through tubing to every key area of the body, and vent tubing will take out the hot internal air this fresh intake air displaces so that the entire robot has great air circulation. The lungs are to look a bit like a small accordion or bellows for a fireplace ie they will have two flat hard plates and a soft gasket that joins the two hard plates and one of the plates will move away from the other plate to draw air in and then the two plates will be smashed back together for air expulsion. A single motor can achieve this. Here's a drawing of this:
This is a rough design of the accordion-like lungs I intend to make for the robot's internal air circulation and evaporative cooling and water cooling systems. This drawing mainly demonstrates the working principle of the way the lungs will open and close as well as valves for opening the inlet and outlet which have to open and close alternately for in-taking fresh air and then pushing that fresh air into the body. I recently realized they can just both be one way valves and don't even need to be motorized that way. The lungs bring the air into the body but never exhale air out of the body they only inhale air into themselves then exhale it into the body and vent exit tubes take care of allowing the hot air that is being displaced by the fresh new outside air to exit the body through the nostrils. The intake is also through the nostrils btw. This way the mouth does not need to open for it to breathe in and out.
This drawing demonstrates the idea of dividing up the air in the lungs into separate compartments for a more even distribution of the air when it draws it into the rest of the system to ensure the whole system gets the correct amount of air to each location. I am not sure if this is needed though as I think further reaches can just have larger diameter tubing and closer reaches can use smaller diameter tubing so the air will divide up automatically that way. Not sure on this. But I have this concept of division into pockets just in case I find issues with most air going to one area and not enough to another area and I can fall back to this pocket distribution idea in that case to solve it. Its just another tool in the bag so to speak.
This drawing is for an idea to use a actual freon based air conditioning system just like cars and window units employ but miniaturized in the robot's lungs. I am leaning toward not doing this anymore since it would add unnecessary weight and complication, but I leave it here for reference and it is a optional tool in the bag just in case we wanted to try it in the future or someone else wants to try similar. I think the ice cube based cooling is a superior approach now because ice can be found anywhere you go or a cold drink and this can cool its water cooling system and make a literal freon-based air conditioner in its chest overkill and unneeded.
These drawings show a simple early sketch for a ice cooling system for the robot and then a more elaborate sketch for it. I've iterated on these designs several times since these were drawn, but these drawings are simple exploded views of how the working principle can look in general. I have improved on these a lot since then but I think these do a good job of demonstrating the concept. The water cooling system will double as a evaporative air conditioner by sending water trickling down netting in the lungs so that when it breathes the air its breath interweaves with the water droplets causing evaporation which triggers the evaporative cooling effect which in turn cools both the air and the water tremendously. Its the same working principle as air hitting sweat - you instantly feel cold on your skin when a fan hits liquid on your skin. That is the evaporative cooling effect in action. So I intend to use this effect to cool air and water within the lungs. The ice cooling reservoir will be a bag that presses flush with the distilled water cooling reservoir bag. The dirty or soda containing or non-distilled water containing ice water or ice juice (whatever the robot can get its hands on for cooling needs) does not have to be pure because its just anything the robot can find in the moment it needs cooling. Even anything from a vending machine it can drink then. It will be kept in its own separate reservoir so it doesn't gum up the main distilled water cooling system. So the ice water/ice cubes/juice etc reservoir presses against the main distilled water cooling reservoir (containing only distilled water which won't gum up or corrode the main water cooling system). And by having the two bags pressed against eachother, the coldness of the one bag cools the distilled water cooling water bag, pulling heat out of that bag quickly. Once the two bags' temperatures reach equilibrium, the robot can then pee out the ice water cooling reservoir bag contents and go get another drink of ice water or cold whatever drink to rinse and repeat that process as needed. I don't anticipate it needing this extra cooling often, but in hot conditions or rigorous work that is quite physical or sports or dancing it would need this to add extra cooling to its existing cooling approaches. It would then "fuel up" on ice water in advance of rigorous physical activity to prevent overheating during said activity.
Note: I originally planned to put the water cooling and ice cooling reservoirs in the chest of the robot but later realized I could instead put them in the belly of the robot more toward the front of the robot and this way the torso has much more room and these reservoirs won't take up so much room in the chest - which is much needed room. So then, when the robot needs ice cooling, it can drink a large volume of ice and cold water (or juice or w/e drink that's cold) and this will fill its ice reservoir bag which will then cause the belly to protrude like a pot belly. This is how humans work since when we eat a ton our belly sticks out. Same principle. This means we get bonus space available for this purpose outside the normal operating space of the robot's torso due to this natural protrusion factor. This bonus extra room in demand is a nice luxury since it means we don't have to accommodate cold water/ice/juice in the precious coveted space within the torso which gives us more room for other important electronics and stuff to fit in.
Note: the reservoirs of the distilled water for the main water cooling system and the ice water reservoir for the ice cooling system both are best being as big as reasonably possible since the bigger the reservoir the more cooling you get and the longer it takes for those bags to heat up and start causing problems with heat. So then the bigger the reservoir the more sustained cooling we get. After both these reservoir's contents get heated up significantly, they are no longer effective at cooling the system and the robot would have to either sit down and rest and wait till these cool down naturally or would need to pee out the ice cooling reservoir bag warm/hot contents and go drink cold liquid and/or ice to fill the bag back up with something that will quickly cool the whole system down again and it can resume work right away this way with no downtime.
Recent Posts
